Tile ratings answer two separate questions: how a glaze resists visible wear, and how much force snaps the body. Neither one measures if a floor is slippery.
Each comes from its own machine and unit, and they fail in unrelated ways. A surface can dull under traffic while the piece beneath stays intact, or the piece can fracture under a furniture leg while its face looks new. Reading a spec sheet means holding both results at once, then asking what the lab never tested: the subfloor, the mortar, and the grit.
The Two Numbers That Matter on a Tile Spec Sheet
A spec sheet lists water absorption, breaking strength, abrasion class, slip resistance, and shade variation. For a home floor, two carry the decision: the abrasion class of the surface and the breaking strength of the body. The specific test behind each number matters more than the number itself.
The abrasion class describes the glaze, the thin fired coating on a glazed tile, and answers how much standardized wear the surface takes before damage becomes visible. Breaking strength describes the whole piece and answers how much force snaps a supported tile. One is a surface property, the other structural.
Neither is a general quality grade, and neither measures slip resistance. The tile flooring guide maps the material and room choice as a whole; the ratings here are the two laboratory numbers that feed that choice, plus the boundaries of what they can tell you.
Wear resistance and breaking strength are independent: a tile can excel at one and fail the other.
PEI / ASTM C1027: Visible Abrasion Classes 0 to V
ASTM C1027 sorts glazed tile into six classes, 0 through V, by the abrasion stage at which wear first becomes visible. The stages are 100, 150, 600, 750, 1500, 2100, 6000, and 12000 revolutions. A higher class means the glaze survived more revolutions before showing damage: a wear ranking, not a strength score.
Class 0 shows wear at 100 revolutions and is a wall rating. Class I reaches 150, Class II 600, and Class III either 750 or 1500.
Class IV covers 2100, 6000, or 12000, and Class V survives past 12000 revolutions plus a stain test. The two stages inside Class III are why some charts split it into a weak and a strong three.
The stain gate is the part most retail charts leave out. A glaze can pass 12000 revolutions and still drop to Class IV if the worn surface holds a stain that will not clean off. Class V means the surface keeps its appearance under heavy traffic, not just low material loss.
| Class | Visible wear at (revolutions) | Typical use |
|---|---|---|
| 0 | 100 | Walls and decorative only |
| I | 150 | Disputed: walls only, or very light residential |
| II | 600 | Light residential, guest baths, low-traffic rooms |
| III | 750 or 1500 | Most residential rooms, normal footwear |
| IV | 2100, 6000, or 12000 | Kitchens, entries, halls, light commercial |
| V | Over 12000, plus stain test | Heavy commercial, airports, malls |
For a home, Class III is the practical minimum for most rooms and Class IV suits kitchens and entries. Class V is a commercial rating. The match is guidance, not a guarantee, because the lab assumes controlled footwear and dirt; for example, a sandy entry or a workshop floor changes the real wear.
How the C1027 Test Actually Works
The test rotates a defined abrasive load on the glazed surface, then asks whether wear is visible. ISO 10545-7, the international equivalent, specifies the load as steel balls of four sizes, white fused aluminium oxide grit, and water.
Each stage uses a fresh specimen, and the tile is classified at the lowest revolution count that shows visible wear.
After each stage the specimen is rinsed, oven-dried, and compared with unabraded tiles in a light box. The endpoint is a visible change, not a measured weight loss.
The viewing is standardized: a darkened room, 300 lux on the tile, observers at 2 meters distance and 1.65 meters eye height, and a consensus of at least three observers.
Because the endpoint is visual, color and finish matter. Darker and high-gloss glazes reveal wear sooner, so the test runs per color rather than once per line, and ASTM C1027 limits comparison to tiles of like color and finish. The method also does not optimally evaluate loss of gloss, a separate appearance question.
A typical run uses eleven test specimens plus eight comparison tiles, and the class applies to that sample set and color. It is a lab result on a controlled abrasive, not a prediction of how your floor will age under your shoes, grit, and cleaning routine.
The machine counts revolutions; a person decides when the wear is visible.
The logic is shared with other flooring wear scales. Laminate uses an AC class built on a similar revolving-abrasive idea, and laminate AC ratings explained maps that scale. The tests, units, and boundaries differ, so a PEI class and an AC class are not interchangeable even when the numbers look alike.

Breaking Strength / ASTM C648 and the ANSI A137.1 Minimums
ASTM C648 measures breaking strength as a force. A tile rests on three supports, a load is applied at the center at a controlled rate, and the result is the pounds-force read from the gauge when the tile snaps.
It is not a pressure. The standard is explicit that tile strength is the force in pounds-force or newtons required to break the tile.
The unit is worth correcting because published guides get it wrong. Some quote breaking strength in psi, but psi is force per unit area and belongs to modulus of rupture or compressive strength, which are different tests.
ASTM C1505 gives a breaking strength in pounds-force and a modulus of rupture in psi from one three-point load. The C648 result is only the force.
Procedure details make the number comparable across labs. A typical report tests ten specimens on supports in a 1.5 inch equilateral triangle, loads at 1000 pounds-force per minute, then averages the ten and records each individual value. One porcelain floor tile averaged 387 pounds-force in a published lab report, well above the minimum.
What breaking strength does a floor tile need?
Under the current ANSI A137.1, porcelain must average at least 275 pounds-force with no individual tile below 250. Non-porcelain pressed floor tile averages 250 with no individual below 225, quarry 275 and 250, mosaic 250 and 225, and glazed wall tile 125 and 100. The minimum is a floor, not a target.
Thickness matters: for the same body, a thicker tile carries a higher breaking force.
That is mechanics, not a separate rating. A 6 mm gauged porcelain panel and a thick porcelain paver can share the same absorption class yet post very different breaking forces, because the force a section resists scales with thickness and density. The minimum applies to the tile type, not to every ceramic product alike.
ANSI A137.1 Water-Absorption Classification
ANSI A137.1 classifies ceramic tile by water absorption, measured by ASTM C373 after a five-hour boil and a 24-hour soak. The percentage of weight gained sorts tile into four classes, driving frost suitability, the breaking-strength minimum, and whether a tile can be called porcelain.
| Absorption class | Water absorbed | Implication |
|---|---|---|
| Non-vitreous | Over 7% | Wall tile; not for freeze-thaw |
| Semi-vitreous | 3% to 7% | Interior only; frost risk |
| Vitreous | 0.5% to 3% | Dense; most interior floors |
| Impervious (porcelain) | 0.5% or less | Frost-resistant; exterior capable |
Porcelain is the impervious class: a ceramic tile with water absorption of 0.5% or less, generally pressed or extruded, and not a low-crystallinity material such as glass. The absorption class is why porcelain suits freeze-thaw exposure and ordinary ceramic often does not, because absorbed water expands when it freezes and cracks the body.
Porcelain is not a different material from ceramic; it is the densest subset of it. The porcelain vs ceramic tile comparison treats the body and firing differences, and porcelain tile flooring is the material explainer. The rating question here is only what the absorption class guarantees.
The Porcelain Tile Certification Agency, run by TCNA and the distributors’ association, certifies the 0.5% criterion through independent lab testing on a recurring cycle. The mark verifies that a tile is really porcelain. It does not certify breaking strength or abrasion class, so a certified porcelain can still carry a modest wear class.
What Each Rating Does NOT Tell You
The two ratings are product tests, not floor tests. Breaking strength measures a supported tile in a lab; it is not the load an installed floor can carry.
Substrate deflection, mortar coverage, and flatness all change installed performance, and a tile above the minimum can still crack over a flexing subfloor or a void under a furniture leg.
The installed floor has its own criteria and its own test. The TCNA deflection limit for ceramic tile is L/360, a system property the tile’s breaking force does not describe.
The Robinson floor test, ASTM C627, rolls a loaded wheel over a tiled assembly to rate the whole system. A product can pass C648 and still fail C627 if the substrate or the bond is weak.
Slip resistance is separate again. ANSI A326.3 sets a dynamic coefficient of friction, or DCOF, of 0.42 or greater for level interior surfaces walked on wet. A Class V glaze can still be slippery when wet, because the wear test measures appearance, not friction. For a bathroom or entry, check the DCOF value, not the PEI class.
Does a higher PEI rating mean a stronger tile?
No. The abrasion class ranks the glaze against visible wear, while breaking strength ranks the body against fracture, on different machines with different units.
A tile can carry Class V and a modest breaking force, or a high breaking force and a low wear class. Neither number is a proxy for the other or an overall quality grade.
Scratch hardness is a third axis. The Mohs scale ranks minerals from talc at 1 to diamond at 10, and quartz sand sits at 7, so tracked sand scratches most glazes. Mohs values are commonly published but are not an ASTM or ANSI requirement, and they do not correlate with the abrasion class.
A wear class is not a scratch rating, and a scratch rating is not a traffic class.
The ratings also say nothing about thickness, rectified edges, or shade variation. A rectified edge is a mechanically cut edge for tighter grout joints, not a strength feature. Shade variation is its own ANSI scale, V0 to V4. Finish is a separate choice again; the tile finish types comparison handles how each surface looks and hides wear.
Why PEI Class Boundaries Differ by Source
The revolution stages are fixed, but the room recommendations attached to each class are not, and the numbering varies by publisher. ASTM C1027 labels its classes 0 to V.
The ISO 10545-7 table also runs 0 to 5 on the same stages, yet many guides present the ISO scale as classes 1 to 5 with no class 0, dropping the wall-only class.
That is a presentation convention, not a different test. When a chart starts at 1, read the revolution count behind the number rather than trusting the digit, because a publisher’s class 1 may mean the 150-revolution stage or may have renumbered the wall-only class. The physics is constant; the label is not.
Is PEI Class I suitable for floors?
The sources genuinely disagree. The Home Depot specification guide lists Class I for light-duty residential floors, specifically bathrooms and bedrooms without direct outside access and no scratching dirt. TileMart’s chart keeps Class 0 and Class I on walls and decorative surfaces only. Other guides map class 1 to very-light floors used in soft-soled shoes.
The disagreement is about scope, not the test. A 150-revolution glaze is marginal on any floor, and every chart that allows it restricts the room to barefoot or soft-soled traffic with no abrasive grit.
For a home, treat Class I as a wall rating unless the room is a low-traffic bathroom or bedroom, and specify Class III or higher wherever shoes and dirt arrive.
When two charts disagree, the revolution count and the room conditions settle it, not the class name.
Why Breaking-Strength Minimums Differ
The breaking-strength disagreement is about editions, and it is still live in manufacturer literature. The current ANSI A137.1 porcelain minimum, as applied in TCNA’s own product-assurance lab testing, is 275 pounds-force average with no individual below 250. The 2008-era requirement, reprinted in the TCNA Handbook of that period, was 250 average with no individual below 225.
Both numbers circulate today. A manufacturer’s 2024 testing white paper lists 250 pounds-force average for porcelain, and the Home Depot guide gives 125 for wall tile and 250 for floor and porcelain tile, the older floor shorthand. Meanwhile a 2025 lab report and a tile consultant’s published answer apply 275 average and 250 individual to porcelain.
The older figure did not vanish when the standard moved, so a sheet quoting 250 for porcelain may be quoting an earlier edition or the general floor-tile minimum, not a weak product. Check the edition and the tile type before comparing, and never average the two numbers.
| Tile type | Current ANSI A137.1 (avg / individual, lbf) | 2008-era ANSI A137.1 / TCNA Handbook (avg / individual, lbf) |
|---|---|---|
| Porcelain | 275 / 250 | 250 / 225 |
| Pressed floor, non-porcelain | 250 / 225 | 250 / 225 |
| Quarry | 275 / 250 | 250 / 225 |
| Mosaic | 250 / 225 | 250 / 225 |
| Glazed wall | 125 / 100 | 125 / 100 |
The tile type matters as much as the edition. Non-porcelain pressed floor tile still carries 250 average and 225 individual in the current standard, so a 250 average on a non-porcelain floor tile is current, not outdated. Porcelain and quarry carry the higher 275 and 250. Reading the type column resolves most apparent contradictions.
There is also a sampling nuance behind every minimum. ANSI A137.1 uses a statistical sampling plan, so a lot can pass with a small fraction of tiles falling short of one property. The class and the minimum describe the lot under that plan, not a guarantee that every tile in every box meets every number.
Unglazed Porcelain: Deep Abrasion Instead of PEI
The PEI test wears a glaze, so it only applies to glazed tile. Unglazed through-body porcelain has no glaze to wear; the color and material run the full thickness.
It carries no PEI class at all, and a sheet that omits the abrasion class for a through-body product is not missing data, it is reporting the right test.
Do porcelain tiles have a PEI rating?
Only the glazed ones. Glazed porcelain has a glaze, and that glaze earns a PEI class like any other glazed tile, so the claim that PEI is meaningless for porcelain is true only for the unglazed through-body type. Reading porcelain on a box does not tell you whether a wear class applies; reading glazed or through-body does.
Through-body porcelain is rated by deep abrasion instead. ASTM C1243 and ISO 10545-6 measure the volume of material removed by a rotating abrasive disc, and the international limit for unglazed tile is a maximum volume loss of 175 mm3.
A lower volume means a denser, more wear-resistant body. The Taber wear index under ASTM C501 is another unglazed measure.
This is why a through-body porcelain can show virtually no wear after decades of traffic: there is no thin surface layer to wear through, so abrasion removes body material gradually rather than exposing a different color underneath. The trade is appearance, not durability, which is a finish question rather than a rating question.
Reading a Real Spec Sheet
A through-body porcelain field tile sheet makes the boundaries concrete. One US product lists a through-body porcelain body with a rectified edge and matte and polished finishes, and carries no PEI abrasion class anywhere, because there is no glaze to wear. The absence is correct, not an omission.
Its water absorption row quotes the ANSI A137.1 porcelain limit of 0.5% or less and marks the series as conforming. Its breaking strength row quotes the ANSI minimum of 250 pounds-force for porcelain, the older floor shorthand, while the series average is 510 pounds-force or more. The minimum and the measured result do different jobs.
The same sheet gives surface hardness as 7 Mohs, shade variation as V1 uniform appearance, and DCOF by finish: interior wet for the matte face and interior dry for the polished face. Bond strength appears in psi, at 50 or more, while breaking strength appears in pounds-force. Two force-related numbers, two units, two tests.
Read together, the sheet shows why no single rating carries the decision: absorption confirms porcelain and frost suitability, breaking force confirms the body exceeds the minimum, Mohs describes scratch hardness, DCOF describes slip, and the missing PEI class means the wear story is deep abrasion.
When a carton label and a spec sheet conflict, the spec sheet with its test method and edition is the better evidence. The manufacturer’s technical department can confirm the current class for a specific color and lot, and samples or showroom boards are general reference rather than a guarantee of the delivered lot.
A floor-tile warranty is typically a manufacturing-defect warranty, not a wear guarantee. It excludes improper installation and structural or environmental conditions, and where it covers surface wear, that coverage is bounded by the published performance class and the care manual. The rating describes the product, not your floor.
Matching Ratings to a Home
Start with the room, not the highest number. For most residential floors, specify a Class III glaze or higher; for a kitchen, entry, or hallway where grit and frequency rise, choose Class IV over Class III. Class V is a commercial rating, and buying it for a bedroom pays for durability the room will never use.
Then check the body against the load. A porcelain floor tile should meet the current 275 pounds-force average and 250 individual minimum, and a non-porcelain floor tile the 250 and 225 minimum. If the sheet quotes an older figure, confirm the edition and the tile type rather than assuming the product is weak.
Then look past the ratings to the numbers they do not cover. For a bathroom or entry, check the DCOF interior-wet classification; for an exterior or freeze-thaw location, check the absorption class; for a large-format tile, confirm the substrate and the bond, because the installed system decides whether the floor survives.
The ratings are evidence, not a verdict on their own. A tile that meets every lab minimum can still fail in a hallway if the subfloor flexes or the mortar leaves voids.
A modest class can serve a low-traffic room for decades. Match the class to the traffic, the body to the load, and the assembly to the substrate.
That is the whole method: read the wear class and the breaking force as two independent results, check the edition and tile type behind each, and remember that slip, scratch, and installed capacity are separate questions the ratings never answer.








